[gcode_macro PRINT_START]
gcode:        
    # Parameters
    {% set bedTemp = params.BED|int %}
    {% set hotendTemp = params.HOTEND|int %}
    {% set DWELL = params.DWELL|default(300)|int %}
    {% set X = 200  %}
    
    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={hotendTemp|float*0.8}  # set extruder pre warm temp
    SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bedTemp}             # set bed temp to warm while starting up
    G28   # home after setting temps
    SET_DISPLAY_TEXT MSG="Waiting for temperatures..."
    TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bedTemp} MAXIMUM={bedTemp+1}  ; Wait for bed temp (within 1 degree)
    HEATSOAK DWELL={DWELL} # Dwelling
    #ATTACH_PROBE  # Have probe ready for calibration
    CLEAN_NOZZLE  # Clean before getting offsets
    G28 Z
    #BED_MESH_CALIBRATE
    #CALIBRATE_Z  # Auto calibrate the bed height
    GO_TO_BUCKET  # No cleanup from nozzle ooze
    SET_DISPLAY_TEXT MSG="Waiting for final temperatures..."
    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={hotendTemp} # Set extruder to printing temperature
    TEMPERATURE_WAIT SENSOR=extruder MINIMUM={hotendTemp} MAXIMUM={hotendTemp+3}  ; Wait for hotend temp (within 3 degrees)
    CLEAN_NOZZLE  # Final clean before print
    SET_DISPLAY_TEXT MSG="Print starting"
    G90
    G1 X{X} F{1000*60} # Avoid brush
    G91

[gcode_macro PRINT_END]
gcode:
    SAFE_RETRACT
    M106 S0  # Part fan off
    TURN_OFF_HEATERS
    GO_TO_BUCKET
    BED_MESH_CLEAR
    DISABLE_MOTORS

[gcode_macro HEATSOAK]
gcode:
    SET_DISPLAY_TEXT MSG="Waiting for thermal expansion..."
    G4 P{params.DWELL|int*1000/4}
    SET_DISPLAY_TEXT MSG="Waiting for thermal expansion 25% done"
    G4 P{params.DWELL|int*1000/4}
    SET_DISPLAY_TEXT MSG="Waiting for thermal expansion 50% done"
    G4 P{params.DWELL|int*1000/4}
    SET_DISPLAY_TEXT MSG="Waiting for thermal expansion 75% done"
    G4 P{params.DWELL|int*1000/4}
    SET_DISPLAY_TEXT MSG="Thermal expansion done"

[gcode_macro CANCEL_PRINT]
rename_existing: BASE_CANCEL_PRINT
gcode:
    M104 S0
    M140 S0
    M106 S0  # Part fan off
    G91 E-2
    CLEAR_PAUSE
    BASE_CANCEL_PRINT
    SDCARD_RESET_FILE
    M221 S100
    BED_MESH_CLEAR

[gcode_macro PAUSE]
rename_existing: BASE_PAUSE
gcode:
    #Edit this#
    {% set Z = 2  %}
    ###########
    SAVE_GCODE_STATE NAME=PAUSE_state
    BASE_PAUSE
    G91
    SAFE_RETRACT
    G1 Z{Z}
    GO_TO_BUCKET
    G91

[gcode_macro RESUME]
rename_existing: BASE_RESUME
gcode:
    #Edit this#
    {% set Z = 10  %}
    ###########
    CLEAN_NOZZLE
    G91
    G1 Z{Z}
    G91
    RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1
    BASE_RESUME

[gcode_macro UNLOAD_FILAMENT]
gcode:
    M118 Filament unloading!
    M117 Filament unloading!
    M82 #set extruder to absolute mode
    G92 E0
    {% if printer.extruder.can_extrude|lower != 'true' %} # checing for minimum extrusion temperature
    # check if temperature is over the minimum extrusion temp. min_extrude_temp must be defined in the extruder config (to about 185)
    M118 Hotend heating!
    M109 S235 T0 # set temperature and wait
    {% endif %}
    G1 E10 F{5*60}    # extrude a little to soften tip
    G0 E-5 F{60*60}   # extract filament to cold end
    G0 E-70 F{5*60}   # continue extraction slow allow filament to be cooled enough before reaches the gears
    M400
    M118 Filament unload complete!
    M117 Filament unload complete!


[gcode_macro M600]
gcode:
  PAUSE

[gcode_macro DISABLE_MOTORS]
gcode:
    M18

[idle_timeout]
gcode:
    TURN_OFF_HEATERS
    DISABLE_MOTORS

[gcode_macro GO_TO_BUCKET]
gcode:
    #Edit this#
    {% set X = 55 %}
    {% set Y = 312 %}
    {% set Z = 2  %}
    ###########
    SAFE_RETRACT
    G91
    G1 Z{Z}
    G90
    G1 X{X} Y{Y} F{1000*60}
    #G1 Y{Y} F{1000*60}
    G91

[gcode_macro safe_retract]
gcode:
    {% if printer.extruder.can_extrude %}
        G10
    {% endif %}

[gcode_macro safe_unretract]
gcode:
    {% if printer.extruder.can_extrude %}
        G11
    {% endif %}