260 lines
4.4 KiB
INI
260 lines
4.4 KiB
INI
[include mainsail.cfg]
|
|
[include macros.cfg]
|
|
[include print_start.cfg]
|
|
[include print_end.cfg]
|
|
[include calibration_macros.cfg]
|
|
#[include klipper-mini12864.cfg]
|
|
[include dock_macros.cfg]
|
|
[include timelapse.cfg]
|
|
[pause_resume]
|
|
[respond]
|
|
|
|
[force_move]
|
|
enable_force_move: true
|
|
# Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION
|
|
# extended G-Code commands. The default is false.
|
|
|
|
[stepper_x]
|
|
step_pin: PB13
|
|
dir_pin: PB12
|
|
enable_pin: !PB14
|
|
endstop_pin: ^PC0
|
|
rotation_distance: 40
|
|
microsteps: 64
|
|
position_endstop: 250
|
|
position_min: 0
|
|
position_max: 250
|
|
homing_speed: 70
|
|
homing_positive_dir: true
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 0
|
|
run_current: .9
|
|
interpolate: False
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PB10
|
|
dir_pin: PB2
|
|
enable_pin: !PB11
|
|
rotation_distance: 40
|
|
full_steps_per_rotation: 200
|
|
microsteps: 64
|
|
endstop_pin: ^PC1
|
|
position_endstop: 230
|
|
position_min: -21
|
|
position_max: 235
|
|
homing_speed: 70
|
|
homing_positive_dir: true
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 2
|
|
run_current: .9
|
|
interpolate: False
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_z]
|
|
step_pin: PB0
|
|
dir_pin: PC5
|
|
enable_pin: !PB1
|
|
rotation_distance: 40
|
|
full_steps_per_rotation: 200
|
|
microsteps: 64
|
|
endstop_pin: ^PC2
|
|
position_endstop: -2.6
|
|
position_max: 250
|
|
homing_speed: 40
|
|
position_min: -8.0
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 1
|
|
run_current: .9
|
|
interpolate: False
|
|
stealthchop_threshold: 0
|
|
|
|
[bed_mesh]
|
|
speed: 200
|
|
horizontal_move_z: 7.5
|
|
mesh_min: 25,35.0
|
|
mesh_max: 225.0,220
|
|
probe_count: 6
|
|
algorithm: lagrange
|
|
mesh_pps: 3
|
|
fade_start: 1
|
|
fade_end: 10
|
|
fade_target: 0
|
|
|
|
[probe]
|
|
pin: PC15
|
|
x_offset: 0.0
|
|
y_offset: 34.5
|
|
z_offset = 6.275
|
|
speed: 25
|
|
samples_result: median
|
|
samples_tolerance: 0.05
|
|
samples_tolerance_retries: 2
|
|
samples: 3
|
|
|
|
[extruder]
|
|
max_extrude_only_distance: 100.0
|
|
step_pin: PB3
|
|
dir_pin: PB4
|
|
enable_pin: !PD2
|
|
rotation_distance: 21.820
|
|
# Tune for extruder
|
|
gear_ratio: 50:17
|
|
microsteps: 64
|
|
full_steps_per_rotation: 200
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC8
|
|
pressure_advance: 0.05
|
|
pressure_advance_smooth_time: 0.040
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PA0
|
|
control = pid
|
|
pid_kp = 27.402
|
|
pid_ki = 1.631
|
|
pid_kd = 115.090
|
|
min_temp: 0
|
|
max_temp: 350
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 3
|
|
run_current: 0.6
|
|
interpolate: False
|
|
|
|
[controller_fan basement_fan]
|
|
pin: PC14
|
|
max_power: 1
|
|
kick_start_time: 0.200
|
|
shutdown_speed: 0
|
|
idle_timeout: 30
|
|
idle_speed: .3
|
|
fan_speed: 0.6
|
|
|
|
[heater_bed]
|
|
heater_pin: PC9
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: PC3
|
|
pwm_cycle_time: 0.0166
|
|
control = pid
|
|
pid_kp = 60.996
|
|
pid_ki = 0.738
|
|
pid_kd = 1260.320
|
|
min_temp: 0
|
|
max_temp: 120
|
|
|
|
[thermistor custom_chamber]
|
|
temperature1: 8
|
|
resistance1: 100000
|
|
temperature2: 144
|
|
resistance2: 1074
|
|
temperature3: 284
|
|
resistance3: 82.78
|
|
|
|
[temperature_sensor chamber]
|
|
sensor_type: custom_chamber
|
|
sensor_pin: PA6
|
|
min_temp: 0
|
|
max_temp: 200
|
|
|
|
[fan]
|
|
pin: PC6
|
|
|
|
# thermally controlled hotend fan
|
|
[heater_fan hotend_fan]
|
|
pin: PC7
|
|
max_power: 1.0
|
|
kick_start_time: 0.100
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
fan_speed: 1.0
|
|
|
|
[temperature_sensor raspberry_pi]
|
|
sensor_type: temperature_host
|
|
min_temp: 10
|
|
max_temp: 100
|
|
|
|
[temperature_sensor mcu_temp]
|
|
sensor_type: temperature_mcu
|
|
min_temp: 0
|
|
max_temp: 100
|
|
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_33FFD8055646303527842243-if00
|
|
|
|
[mcu rpi]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
[adxl345]
|
|
cs_pin: rpi:None
|
|
|
|
[printer]
|
|
kinematics: corexz
|
|
max_velocity: 200
|
|
max_accel: 7000
|
|
max_accel_to_decel: 3500
|
|
max_z_velocity: 70
|
|
max_z_accel: 7000
|
|
square_corner_velocity: 8.0
|
|
|
|
[static_digital_output usb_pullup_enable]
|
|
pins: !PA14
|
|
|
|
[output_pin LIGHTS]
|
|
pin: PC12
|
|
value: 0
|
|
shutdown_value: 0
|
|
|
|
[screws_tilt_adjust]
|
|
screw1: 125,84.5
|
|
screw1_name: center screw
|
|
screw2: 20,-21
|
|
screw2_name: front left screw
|
|
screw3: 125,-21
|
|
screw3_name: front center screw
|
|
screw4: 230,-21
|
|
screw4_name: front right screw
|
|
screw5: 230,84.5
|
|
screw5_name: center right screw
|
|
screw6: 230,180
|
|
screw6_name: rear right screw
|
|
screw7: 125,180
|
|
screw7_name: rear center screw
|
|
screw8: 20,180
|
|
screw8_name: rear left screw
|
|
screw9: 20,84.5
|
|
screw9_name: center left screw
|
|
horizontal_move_z: 7.5
|
|
speed: 200
|
|
screw_thread: CCW-M3
|
|
|
|
[virtual_sdcard]
|
|
path: /home/pi/sdcard
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
probe_points:
|
|
125,119,20
|
|
|
|
[firmware_retraction]
|
|
retract_length: 0.2
|
|
retract_speed: 80
|
|
unretract_speed: 80
|
|
|
|
[input_shaper]
|
|
shaper_type_x = mzv
|
|
shaper_freq_x = 51.0
|
|
shaper_type_y = mzv
|
|
shaper_freq_y = 48.8
|