Klicky

basic_macros.cfg

@@ -13,7 +13,7 @@ gcode:
     {% set travel_speed = 300 %} # in mm/s
     {% set z_speed = 5 %} # in mm/s
 
-    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={hotendTemp|float*0.6}       # Set extruder pre warm temp
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={hotendTemp|float*0.6}       # Set extruder chamber warm temp
     SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bedTemp}                  # Set bed temp to warm while starting up
     G28                                                                        # home after setting temps
     M117 Waiting for bed temperature...
@@ -21,6 +21,7 @@ gcode:
     {% if chamberTemp != 0 %}                                                  # If chamber temp set
         CHAMBER_WARMER TEMPERATURE={chamberTemp}                               # Warm chamber
     {% endif %}
+    SET_HEATER_TEMPERATURE HEATER=extruder TARGET={hotendTemp|float*0.8}       # Set extruder don't drip temp
     Z_TILT_ADJUST                                                              # Z-Tilt after soak
     G28 Z                                                                      # Rehome Z as it's not the same
     G90                                                                        # Absolute positioning
@@ -149,7 +150,7 @@ gcode:
     {% set x_start = 20 %}
     {% set y_start = 0 %}
     {% set z = 0.3 %}
-    {% set length = 80 %}
+    {% set length = 85 %}
 
     G92 E0                                                   # Reset extruder position
     M117 Purging Nozzle...
@@ -164,10 +165,10 @@ gcode:
 description: Purges along Y in the positive direction, and half a line back
 gcode:
     # User parameters
-    {% set x_start = 0 %}
+    {% set x_start = 1 %}
     {% set y_start = 20 %}
     {% set z = 0.3 %}
-    {% set length = 80 %}
+    {% set length = 85 %}
 
     G92 E0                                                   # Reset extruder position
     M117 Purging Nozzle...

moonraker.conf

@@ -44,4 +44,3 @@ type: git_repo
 primary_branch: main
 path: ~/moonraker-timelapse
 origin: https://github.com/mainsail-crew/moonraker-timelapse.git
-

printer.cfg

@@ -53,11 +53,17 @@ min_temp: 0
 max_temp: 100
 
 [temperature_sensor chamber]
-sensor_type: ATC Semitec 104GT-2
+sensor_type: Generic 3950
 sensor_pin: skrPico:gpio27
 min_temp: 0
 max_temp: 100
 
+[temperature_sensor chamber2]
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: skrPico:gpio26
+min_temp: 0
+max_temp: 100
+
 #####################################################################
 #      X/Y Stepper Settings
 #####################################################################
@@ -133,8 +139,8 @@ pid_kp = 27.030
 pid_ki = 1.540
 pid_kd = 118.596
 min_temp: 0
-max_temp: 320
 min_extrude_temp: 200
+max_temp: 350
 max_extrude_only_distance: 300
 max_extrude_cross_section: 300
 
@@ -208,9 +214,9 @@ timeout: 1800
 pin: skrPico:gpio25
 sample_retract_dist: 4.0
 samples: 1
-dock_position: 0, 115.7, 10
-approach_position: 24, 115.5
-detach_position: 0, 24
+dock_position: 120, 115.5, 10
+approach_position: 90, 115.5
+detach_position: 120, 80
 check_open_attach: True
 dock_fixed_z: True
 dock_retries: 3
@@ -218,18 +224,21 @@ attach_speed: 15
 detach_speed: 15
 travel_speed: 50
 post_attach_gcode:
-    G0 X24 Y115.5
+    G0 X90 Y115.5
+detach_gcode:
+    # Klicky really don't want to let go. Go slow
+    G0 X120 Y80 F{15*60}
 allow_delayed_detach: False
 
-x_offset: -16
-y_offset: 17
-z_offset = 9.815
+x_offset: 30
+y_offset: -2.4
+z_offset = 14.635
 
 [bed_mesh]
 speed: 120
-horizontal_move_z: 12
-mesh_min: 5, 17
-mesh_max: 97, 97
+horizontal_move_z: 2
+mesh_min: 8, 22.4
+mesh_max: 110, 105
 probe_count: 6
 
 [gcode_arcs]

sensorless.cfg

@@ -12,7 +12,7 @@ gcode:
     G28 X0
     # Move away
     G91
-    G1 X24 F{400*60} # dodge probe
+    G1 X60 F{400*60} # dodge probe
     # Set current during print
     SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR}
     SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CUR}
@@ -47,11 +47,9 @@ gcode:
     SENSORLESS_HOME_Y
     # Home Z
     G28 Z0
-    #G1 Z{printer.toolhead.axis_minimum.z + 10} F1200
 
 [homing_override]
 axes: xyz
-set_position_z: -1.8
 
 gcode:
     {% set home_all = 'X' not in params and 'Y' not in params and 'Z' not in params %}
@@ -66,8 +64,7 @@ gcode:
 
 
     {% if home_all or 'Z' in params %}
-        SET_GCODE_OFFSET Z=0.0 # Reset offset before homing Z
-        G28 Z0
+        G28 Z
         G91
     {% endif %}
     G90

tri_zero.cfg

@@ -23,6 +23,7 @@ position_min: -3
 homing_speed: 10
 second_homing_speed: 3
 homing_retract_dist: 8
+homing_positive_dir: False
 
 [tmc2209 stepper_z]
 uart_pin: skrPico:gpio9
@@ -72,10 +73,10 @@ z_positions:
     60, 141
     167.5, 15
 points:
-    30, 0
-    80, 75
-    108, 0
+    0, 26
+    30, 90
+    80, 24
 speed: 500
-horizontal_move_z: 15
+horizontal_move_z: 18
 retries: 15
-retry_tolerance: 0.025
+retry_tolerance: 0.0125